METHOD	DESCRIPTION	SAMPLE  REQ'D	PRICE  US $
0225B	Mean Hertz Load by Shell 4-Ball, Dow Corning Method	200 ml	159.00
0351B	Wear Scar by 4-Ball, Dow Corning Method	200 ml	63.00
ASTM B-117	Salt Spray Corrosion Test @ 48 hrs (Also see FTM-4001)	1 pt	171.00
ASTM B-117	Salt Spray Corrosion Test @ 100 hrs	1 pt	224.00
ASTM B-117	Salt Spray Corrosion Test @ 1000 hrs.	1 pt	453.00
ASTM D-56	Flash Point, Tag Closed Cup	50 ml	55.00
ASTM D-86	Distillation, High Temperature of Petroleum Products	100 ml	86.00
ASTM D-88	Viscosity SUS (See ASTM D-2161)	50 ml	49.00
ASTM D-91	Precipitation Number	200 ml	30.00
ASTM D-92	Flash or Fire Point, Cleveland Open Cup	100 ml	55.00
ASTM D-92	Flash and Fire Points, Cleveland Open Cup	100 ml	69.00
ASTM D-93	Flash Point, Pensky Martin Closed Cup	100 ml	55.00
ASTM D-94	Saponification Number	100 ml	112.00
ASTM D-95	Water by Distillation	100 ml	63.00
ASTM D-97	Pour Point	100 ml	75.00
ASTM D-130	Copper Strip Corrosion	100 ml	52.00
ASTM D-189	Carbon Residue, Conradson of Petroleum Products	20 ml	57.00
ASTM D-287	Gravity, API	500 ml	30.00
ASTM D-395	Compression Set of Elastomers	500 ml	338.00
ASTM D-445	Kinematic Viscosity   Ambient + to 401°F	50 ml	34.00
ASTM D-445	Kinematic Viscosity   Low Temp. to -65°F	50 ml	74.00
ASTM D-471	Elastomer Testing		by request
ASTM D-482	Ash Content of Petroleum Products	50 g	172.00
ASTM D-524	Carbon Residue, Ramsbottom	20 ml	57.00
ASTM D-567	Viscosity Index (needs 100°F & 210°F D-445 Viscosities)		12.00
ASTM D-611	Aniline Point	100 ml	132.00
ASTM D-638	Tensile Strength	500 g	by request
ASTM D-664	Acid Number, Potentiometric	50 ml	36.00
ASTM D-664	Acid Number, Strong	50 ml	55.00
ASTM D-665	Rust Prevention Procedure A or B	1 ltr	109.00
ASTM D-874	Sulfated Ash	50 g	109.00
ASTM D-877	Dielectric Breakdown Volatage of Insulting Liquids Using Disk Electrodes	300 g	61.00
ASTM D-891 A	Specific Gravity Procedure A - Hydrometer	500 ml	30.00
ASTM D-891 B	Specific Gravity Procedure B - Pycnometer	50 ml	63.00
ASTM D-892	Foaming Characteristics - Seq. I	200 ml	46.00
ASTM D-892	Foaming Characteristics - Seq. I, II, III	500 ml	97.00
ASTM D-892	Foaming Characteristics - Seq. I, II, III, IV (Mercon)	500 ml	161.00
ASTM D-893	Pentane and Toluene Insolubles	50 ml	120.00
ASTM D-924	Dielectric Constant/Dissipation Factor (or Power Factor) nad Relative Permittivity of Electrical Insulating Liquids @ Ambient Temperature	50 g	215.00
ASTM D-924	Dielectric Constant/Dissipation Factor (or Power Factor) nad Relative Permittivity of Electrical Insulating Liquids Above Ambient Temperature	50 g	259.00
ASTM D-943	Oxidation Stability (TOST) up to 2000 hrs.	1 ltr	430.00
ASTM D-943	Oxidation Stability (TOST) Per Day After 2000 hrs.		2.00
ASTM D-972	Evaporation Loss @ 6 1/2 hrs.	25 ml	66.00
ASTM D-972	Evaporation Loss @ 22 hrs.	25 ml	79.00
ASTM D-972	Evaporation Loss @ 72 hrs.	25 ml	106.00
ASTM D-972	Evaporation Loss @ 500 hrs.	25 ml	207.00
ASTM D-974	Neutralization Number, Color	50 ml	36.00
ASTM D-1078	Distillation Range of Volatile Organic Liquids	100 ml	109.00
ASTM D-1093	Acidity of Water Layer	100 ml	32.00
ASTM D-1119	Ash Content of Engine Coolants	50 ml	63.00
ASTM D-1122	Specific Gravity	500 ml	30.00
ASTM D-1169	Volume Resistivity - Specific Resistance of Electrical Insulating Liquids	500 g	287.00
ASTM D-1209	Color (Platinum Cobalt Scale)	200 ml	172.00
ASTM D-1218	Refractive Index of Viscous Materials	10 ml	29.00
ASTM D-1275	Corrosive Sulfur in Electrical Insulating Oils	300 ml	263.00
ASTM D-1298	Gravity, Specific	500 ml	30.00
ASTM D-1310	Flash Point, Tag Open Cup	100 ml	56.00
ASTM D-1331	Surface Tension	100 ml	47\9.00
ASTM D-1353	Non-Volatile Residue		88.00
ASTM D-1401	Emulsion Characteristics @ 54°C or 82°C	100 ml	76.00
ASTM D-1414	Rubber Swell	500 ml	126.00
ASTM D-1481	Density by Lipkin Bicapillary Pycnometer	50 ml	63.00
ASTM D-1500	Color, by ASTM Color Scale	100 ml	14.00
ASTM D-1747	Refractive Index of  Viscous Material	10 ml	29.00
ASTM D-1748	Humidity Cabinet Test @ 100 hrs	500 ml	247.00
ASTM D-1748	Humidity Cabinet Test @ 400 hrs	500 ml	330.00
ASTM D-1748	Humidity Cabinet Test @ 1000 hrs	500 ml	440.00
ASTM D-1796	Water and Sediment	200 ml	57.00
ASTM D-1816	Dielectric Breakdown Voltage of Insulating Liquids of Petroluen Origin Using UDE Electrodes	500 g	72.00
ASTM D-1957	Hydroxyl Number	20 g	166.00
ASTM D-2070	Thermal Stability of Hydraulic Oils-Cincinnati Milacron	300 ml	258.00
ASTM D-2074	Amine Value		83.00
ASTM D-2110	pH of Water Extracted from Halogenated Organic Solvents	200 ml	36.00
ASTM D-2112	Rotating Bomb Oxidation Test (RBOT) Up to 48 hours -  per bomb	200 ml	144.00
ASTM D-2112	RBOT Running Time After 48 hours -  per hour		1.00
ASTM D-2155	Autoignition Temperature	50 ml	132.00
ASTM D-2161	SUS (Calculation)		40.00
ASTM D-2196	Brookfield Viscosity Profile Scanning Technique		325.00
ASTM D-2270	Viscosity Index (Calculation) needs 40°C & 100°C D-445 Viscosities		12.00
ASTM D-2272	Rotating Bomb Oxidation Test (RBOT)  Up to 48 hours -  per bomb	200 ml	144.00
ASTM D-2272	RBOT Running Time After 48 hours -  per hour		1.00
ASTM D-2273	Contamination, Trace Sediment	200 ml	43.00
ASTM D-2416	Conradson Carbon Residue	50 ml	57.00
ASTM D-2440	Oxidation Stability of Mineral Insulating Oil @ 72 hrs.	100 ml	201.00
ASTM D-2440	Oxidation Stability of Mineral Insulating Oil @ 164 hrs.	100 ml	212.00
ASTM D-2500	Cloud Point of Transparent Fluids	100 ml	63.00
ASTM D-2502	Molecular Weight from Viscosity - Calculation		12.00
ASTM D-2532	Kinematic Viscosity, Storage 72 hrs. (0 to -65°F)	50 ml	201.00
ASTM D-2595	Evaporation Loss @ 6 1/2 hrs	25 ml	66.00
ASTM D-2595	Evaporation Loss @ 22 hrs.	25 ml	79.00
ASTM D-2595	Evaporation Loss @ 72 hrs.	25 ml	106.00
ASTM D-2595	Evaporation Loss @ 500 hrs.	25 ml	207.00
ASTM D-2595	Evaporation Loss Exceeding 500 hrs - per hour charge		0.20
ASTM D-2603	Sonic Shear Stability	100 ml	315.00
ASTM D-2619	Hydrolytic Stability	200 ml	179.00
ASTM D-2670	Falex Pin & V Block Tooth Wear Test	150 ml	111.00
ASTM D-2711	Demulsibility Characteristics Procedure A or B	500 ml	227.00
ASTM D-2714	Block on Ring Friction & Wear Test  - per run	200 ml	215.00
ASTM D-2782	Timken Load Carrying Test - per load	1 gal	126.00
ASTM D-2783	Load Wear Index - Four Ball EP	200 ml	143.00
ASTM D-2783	Load Wear Index - Weld Load Only	100 ml	109.00
ASTM D-2878	Molecular Weight, by Evaporation & Vapor Pressure	50 ml	190.00
ASTM D-2878	Vapor Pressure, Apparent	50 ml	261.00
ASTM D-2879	Vapor Pressure by Isoteniscope   Single Point	10 ml	111.00
ASTM D-2879	Vapor Pressure by Isoteniscope   - additional temperatures		27.00
ASTM D-2879	Vapor Pressure by Isoteniscope   Multi Point Graph	10 ml	226.00
ASTM D-2893	Oxidation Stability of EP Gear Oils	500 ml	179.00
ASTM D-2896	Base Number (Perchloric Acid Method)	10 ml	149.00
ASTM D-2942	Total Acid of Halogenated Organic Solvents		36.00
ASTM D-2983	Brookfield Viscosity	100 ml	132.00
ASTM D-2989	Acidity-Alkalinity of Halogenated Solvents & Mixtures	200 ml	36.00
ASTM D-3233	Falex Pin & V Block Test  Procedure A or B	150 ml	111.00
ASTM D-3238	Carbon Distribution	100 ml	258.00
ASTM D-3427	Air Release Properties	200 ml	221.00
ASTM D-3520	Quenching Time of Heat Treating Fluids	500 ml	247.00
ASTM D-3703	Peroxide Number of Aviation Fuels	20 g	172.00
ASTM D-3947	Specific Heat by DSC - Discontiued use ASTM E-1269	5g	375.00
ASTM D-3829	Borderline Pumping Temperature   (per temp)	100 ml	172.00
ASTM D-4172	Four Ball Wear	50 ml	63.00
ASTM D-4172	Four Ball Wear @ 2 hrs.	50 ml	83.00
ASTM D-4172	Four Ball Wear @ 4 hrs.	50 ml	106.00
ASTM D-4172	Four Ball Wear with Coefficient of Friction	50 ml	120.00
ASTM D-4172	Four Ball Wear with Coefficent of Friction @ 2 hrs.	50 ml	140.00
ASTM D-4172	Four Ball Wear M-50 Steel Balls	50 ml	114.00
ASTM D-4310	Sludging Tendencies of Inhibited Mineral Oil	500 ml	568.00
ASTM D-4377	Water Content, Karl Fischer	50 ml	76.00
ASTM D-4627	Iron Chip Corrosion	20 g	207.00
ASTM D-4636	Oxidation & Corrosion Stability @ 72 hrs	250 ml	291.00
ASTM D-4636	Oxidation & Corrosion Stability @ 168 hrs	250 ml	338.00
ASTM D-4636	Oxidation & Corrosion Stability per Sampling Interval		52.00
ASTM D-4684	Yield Stress/Apparent Viscosity (MRV)  per temp	100 ml	338.00
ASTM D-4739	Total Base Number by Hydrochloric Acid Method	20 g	55.00
ASTM D-4742	Thin Film Oxygen Uptake Test (TFOUT)	20 g	233.00
ASTM D-4898	Gravimetric Analysis by Filtration	100 ml	45.00
ASTM D-5133	Viscosity, Scanning Brookfield	300 ml	256.00
ASTM D-5293	Apparent Viscosity - Cold Cranking Simulator	30 ml	44.00
ASTM D-5306	Flame Propagation	50 ml	83.00
ASTM D-5620	Falex Pin & V Block Test on Thin Film Lubricants	150 ml	111.00
ASTM D-5621	Sonic Shear Stability	100 ml	315.00
ASTM D-5621	Sonic Shear Stability with Viscosities @ 40°C & 100°C	100 ml	384.00
ASTM D-5768	Iodine Number - WIJS	50 ml	143.00
ASTM D-6082	Foam Test, High Temperature	600 ml	86.00
ASTM D-6138	EMCOR Rust Test - per Bearing	200 ml	263.00
ASTM D-6200	Cooling Characteristics of Quenching Oils	4000 ml	287.00
ASTM D-6200	Water Conent, Karl Fischer	50 ml	76.00
ASTM D-6375	Thermogravimetric Analysis, NOACK Method		by request
ASTM D-6482	Cooling Characteristics of Aqueous & Water Soluble Materials	4000 ml	287.00
ASTM D-6547	Corrosivesness (bimetallic couple)		52.00
ASTM D-6793	Bulk Modulus	200 ml	247.00
ASTM E-659	Autoignition Temperature	50 ml	132.00
ASTM E-1064	Water Content		76.00
ASTM E-1269	Specific Heat By DSC	5 g	375.00
ASTM E-1719	Vapor Pressure by Ebulliometry	100 ml	226.00
ASTM F-312	Particulate Contamination of Oil by Filtration	1 qt	109.00
ASTM F-313	Contaimination, Gravimetric	200 ml	120.00
BT-7	Navistar Water Tolerance	100 ml	86.00
BT-9	Navistar Humidity Corrosion	100 ml	247.00
BT-10	Navistar Oxidation & Corrosion	200 ml	453.00
BT-13	Navistar Stability Heating Test	500 ml	201.00
BT-20	Navistar Load Carrying Ability	200 ml	1,929.00
BT-30	Navistar Foaming Characteristics	1 qt	265.00
CEC L-85-T-99	DSC (Differential Scanning Calorimetry)		276.00
DIN-51381	Air Release Properties per Temperature	200 ml	221.00
DIN-51587	Aging Behavior of Steam Turbine Oils	500 ml	410.00
DIN-51802	EMCOR Rust Test   per bearing	200 ml	263.00
DIN-53169	pH @ 20°C	100 ml	23.00
DIN-53521	Rubber & Elastomer Behavior	500 g	292.00
EPA 24	Determination of Volatile Matter		39.00
EPA5530	Phenol Content	50 g	338.00
FTM-202	Cloud Intensity, Barium Chloride Technique	200 ml	155.00
FTM-350	Evaporation Loss @ 6 1/2 hrs.	25 ml	66.00
FTM-350	Evaporation Loss @ 22 hrs.	25 ml	79.00
FTM-350	Evaporation Loss @ 72 hrs.	25 ml	106.00
FTM-352	Wick Ignition	100 ml	40.00
FTM-3007	Water Displacement & Stability	100 ml	125.00
FTM-3009	Contamination, by HIAC Paticle Counter	200 ml	76.00
FTM-3010	Contamination, Gravimetric  and Ash Residue by Filtration	1 ltr	120.00
FTM-3012	Contamination, Particulate of Oils by HIAC	1 ltr	109.00
FTM-3213	Static Foam Test		86.00
FTM-3403	Compatibility of Turbine Oils (per oil)	1 ltr	97.00
FTM-3411	Thermal Stabiltiy and Corrosivity	100 ml	224.00
FTM-3432	Compatibility of FKM Elastomer	500 ml	258.00
FTM-3433	Navy S Silicone Rubber, Swelling and Tensile Strength	500 ml	258.00
FTM-3456	Channel Point of Lubricating Oils	1 qt	86.00
FTM-3457	Hydrolytic Stability	200 ml	179.00
FTM-3458	Stability, Low Temperature, 72 hrs.	200 ml	155.00
FTM-3459	Stability, Low Temperature, 72 hrs.	200 ml	155.00
FTM-3471	Refractive Index		28.00
FTM-3480	Volatility 24 hrs.		52.00
FTM-3603	Swelling of Rubber   NBR-L  @ 168 hrs	400 ml	126.00
FTM-3604	Swelling of Rubber   NBR-H  @ 72 hrs	400 ml	111.00
FTM-3604	Swelling of Rubber   NBR-H  @ 168 hrs	400 ml	126.00
FTM-4001.2	Salt Spray Corrosion  @ 48 hrs (Aslo see ASTM B-117)	1 pt	171.00
FTM-4001.2	Salt Spray Corrosion  @ 100 hrs	1 pt	224.00
FTM-4001.2	Salt Spray Corrosion  @ 300 hrs	1 pt	325.00
FTM-4001.2	Salt Spray Corrosion  @ 500 hrs	1 pt	386.00
FTM-4001.2	Salt Spray Corrosion  @ 1000 hrs	1 pt	453.00
FTM-5305	Silver Corrosion	500 ml	86.00
FTM-5306	Corrosiveness of Cutting Fluid	100 ml	171.00
FTM-5307	Oxidation & Corrosion Stability @ 72 hrs	250 ml	291.00
FTM-5307	Oxidation & Corrosion Stability @ 168 hrs	250 ml	338.00
FTM-5307	Oxidation & Corrosion Stability per Sampling Interval		52.00
FTM-5308	Oxidation & Corrosion Stability @ 72 hrs	250 ml	291.00
FTM-5308	Oxidation & Corrosion Stability @ 168 hrs	250 ml	338.00
FTM-5321	Lead Corrosion, SOD Method	600 ml	109.00
FTM-5322	Galvanic Corrosion, Clip Test - Salt Spray	600 ml	109.00
FTM-5322	Corrosivity Clip Test (Bimetallic Couple)	1 ptl	52.00
FTM-5329	Humidity Cabinet Test @ 100 hrs.	500 ml	247.00
FTM-5329	Humidity Cabinet Test @ 400 hrs.	500 ml	330.00
FTM-5329	Humidity Cabinet Test @ 900 hrs.	500 ml	413.00
FTM-6052	High Temperature High Pressure Spray Ignition	1 gal	303.00
FTM-6053	Manifold Ignition @ 1,300°F	100 ml	193.00
FTM-6503	Mean Hertz Load	50 g	215.00
GM 4298P	Neutral Salt Spray, General Motors Specification	500 ml	109.00
IP-220	EMCOR Rust Test   per bearing	200 ml	263.00
ISO-760	Moisture by Weight		76.00
ISO-1817	Swelling of Rubber 168 hrs. @ 100°C	500 g	126.00
ISO-2160	Copper Corrosiveness	100 ml	52.00
ISO-2211	Color of Clear Liquids		172.00
ISO-4406	Contamination, Particulate by HIAC Particle Counter	1 qt	109.00
ISO-6072	Elastomer Compatibility		435.00
ISO-6618	Acid Number	500 g	36.00
ISO-7120	Rust Prevention	100 ml	83.00
ISO-15029	Spray Ignition Charateristics		151.00
LUX 5.3.1	Aging Properties		430.00
LUX 5.9	Corrosion Inhibition	2 ltr	373.00
LUX 7.6	Rust Prevention Procedure	500 ml	83.00
LUX 7.10	Evapration for HFC Fluid @ 168 hrs.	50 ml	170.00
PLTL-58	Microscopic Examination	10 g	52.00
PLTL-59	Hughes Specification Humidity Cabinet @ 20 hours	500 ml	86.00
PLTL-61	GC Analysis		by request
PLTL-73	Thermal Conductivity by DSC - Specify temperature	2 gm	303.00
PLTL-78	Infrared Spectra - FTIR	trace	51.00
PLTL-85	Molecular Weight, Boiling Point Elevation TechniqueTechnique	20 ml	166.00
PLTL-87	Iron Contamination by Magneto Extraction	100 ml	63.00
PLTL-92	Coefficient of Expansion by Pycnometer	25 ml	83.00
PLTL-95	Friction Analysis, Rolling Contact	20 ml	181.00
PLTL-108	DSC Thermogram	1 g	191.00
PLTL-123	Blue Soap Test	20 g	45.00
PLTL-140	Vapor Density	50 g	248.00
PLTL-149	Oxidation Onset Temperature	5 g	184.00
PLTL-156	Reichert Test	100 ml	138.00
SAE ARP 598B	Particle Count	200 ml	76.00
SAE  J1165	ISO Cleanliness Code	100 ml	74.00
USP Visc	USP Brookfield Viscosity	100 g	131.00
WQTM-611	Paricle Count, BASF Method		109.00